Technical Mentoring & Elmering Net

The timestamps below are best followed by downloading the Mp3 file here and listening with Windows Media Player.

The Technical Mentoring and Elmering net on Thursday, June 18th had 10 check-ins plus net control Dave (K6HWN). Discussions included:

00:12:00 Shackmaster Dave’s thought experiment/idea that of someone in Santa Barbara with a good gain antenna on the roof for 2 Meters terminated in a 50 ohm resistor or germanium diode. And, if they had the ability to feed into that diode at will when they flip the switch on or off, a signal of .81 MHz pure sine wave from an audio generator. With that set up and the .81 MHz signal was turned on, what would happen or be heard? Listen to the discussion and thoughts here.

00:24:20 Brian (K6BPM) had a question that when he is transmitting via RMS Express radio e-mail program (www.winlink.org) on 40 Meters the signal can be heard when he’s transmitting at the same time on 2 Meters, specifically the K6TZ repeater! The other hams listening to the net on 2 Meters could hear this artifact through their 2 M rigs speaker as far away from Santa Barbara as Port Hueneme while Brian was transmitting.  Hear some thoughts regarding this phenomenon here.

00:35:00 I (K6FLD) asked Dennis (WB6OBB) if he had ever heard anything like my in-wall noise issue when I transmit on certain HF frequencies with my new end-fed antenna. I sounds like a loud hum emanating from the walls in the house and if the hair dryer is plugged in, the plug with GFI rattles like crazy and trips the GFI! Hear more about that here.

As I mentioned before, you can listen to the entire audio archive or go to the approximate time stamp listed at the beginning of each subject. It’s most accurate if you download the .mp3 audio file and play it in Windows Media Player or similar program.

Tune in to the SBARC Technical Mentoring and Elmering Net next Thursday at 8:00 PM or 2000 Hrs  and see what interesting questions will arise or ask some of your own! All club members and visitors are encouraged to check in to the Technical Mentoring and Elmering net each week and join in with questions and /or answers to and contribute the knowledge of new and seasoned amateur radio operators alike.

K6HMD provided two technical documents describing how circulators work. There are available for download here:

http://www.sbarc.org/downloads/circulator.pdf

http://www.sbarc.org/downloads/tx-rx-intro-to-ferrite-isolators-circulators-and-rf-loads.pdf

The Technical Mentoring and Elmering for Thursday, June 11th had 9 check-ins plus net control Dave (K6HWN). Discussions included Hayden’s (KK6OYV) fractional wave antenna construction progress and he’s promised to take pictures of the different stages and share them on his website when it’s up and running. Jim (KK6SXB) added to the conversation stating that there are magnetic loop and Faraday loop antennas but the fractional wave antenna gets its name because of the helically wound copper strapping that surrounds it.

I (K6FLD) had a question about why there were different types of amplifiers to consider when choosing one for the different ham bands we might operate on. Shackmaster (K6HWN) explained that for VHF and above its handed a little differently as it’s not practical to tune for the different bands. The amplifiers are made specific to the VHF/UHF bands and there’s just not that much need tune because the bands are relatively close in frequency. For HF 160-10 meters maybe even 6 meters you will need to tune your amplifier as often as your antenna for the bands. Also of you’re operating SSB the amplifier needs to be a linear amp, not so if just FM. You can listen to the audio archive of the net here.

Tune in to the SBARC Technical Mentoring and Elmering Net next Thursday at 8:00 PM or 2000 Hrs  and see what interesting questions will arise or ask some of your own! All club members and visitors are encouraged to check in to the Technical Mentoring and Elmering net each week and join in with questions and /or answers to and contribute the knowledge of new and seasoned amateur radio operators alike.

Note:  The timestamps listed below are best followed by downloading the Mp3 file here and listening with Windows Media Player or similar program.

The Technical Mentoring and Elmering net on Thursday, June 4th yielded 11 check-ins plus net control Dave (K6HWN).

00:08:40 – Gary (KK6KPJ) started the net off with a question about a simple to use 2 m radio without all the bells and whistles. He’s not interested in programming frequencies and memory channels. Several comments were made by Hayden (KK6OYV) and Shackmaster Dave (K6HWN) confirmed Hayden’s point of view that the older the radio the fewer advanced features it’ll have and he mentioned a couple of Yeasu that might work.

00:24:03 – Eric (KG6WXC) wondered how the club station could have so many different radios in use and not interfere with each other. Shackmaster explained that with the casual type of operating done at the station, a really good grounding system, and the antennas in different places that the radios pretty much stayed clear of one another.

00:27:40 – Shackmaster asked Glen (WZ) more about his setup and somehow connecting Lompoc hams to Santa Barbara hams and allowing them to listen in to our nets and communicate with us, etc. Glen has a 220 beam antenna and a new radio at 50 watts and he beams solidly into 224.08. Glen mentioned that he hadn’t had time to consult with some of the local hams there but would at the next club meeting coming up this Saturday so the discussion will continue down the road.

00:31:05 – Ken (KA6KEN) asked questions about using an amplifier in conjunction with a tuner and the procedures necessary to keep the antenna and amplifier tuned as he might transgress the different amateur bands. A lot of valuable information can be learned about this and related subjects including the different types of amplifiers by listening to the audio recording of the net here.

01:00:40 – Gary (KK6KPJ) asked about using an antenna tuner with 2 m radios, say if the antenna were up at 30 ft. or so. Shackmaster has never known or heard of a 2 m antenna tuner. The frequency difference from one end of the band to the other is quite small as compared to HF frequencies so there’s no need to re-tune as you spin the VFO around. You’d pretty much just set it up correctly on the bench, mount the antenna an d go.

As I mentioned before, you can listen to the entire audio archive or go to the approximate time stamp listed at the beginning of each subject. It’s most accurate if you download the .mp3 audio file and play it in Windows Media Player or similar program.

Tune in to the SBARC Technical Mentoring and Elmering Net next Thursday at 8:00 PM or 2000 Hrs  and see what interesting questions will arise or ask some of your own! All club members and visitors are encouraged to check in to the Technical Mentoring and Elmering net each week and join in with questions and /or answers to and contribute the knowledge of new and seasoned amateur radio operators alike.

The Technical Mentoring and Elmering net on Thursday 5/28/15 yielded 9 check-ins plus net control Dave (K6HWN).

The timestamps below are best followed by downloading the Mp3 file here and listening with Windows Media Player.

00:08:00 – Jim (KK6SXB) started the net off asking questions of Brian (K6BPM) regarding setting up for digital modes. It seems that Jim has recently acquired two devices (SDRplay and Airspy boxes) that he’d like to use in setting up the ability to use digital ham radio modes with his computer. The HDSDR software he also acquired along with the correct supporting driver software will display 8+ MHz of any band on the computer screen giving you visibility of any signal there. So basically what he’s purchased should get him receiver and display capability but to actually practice digital modes on ham radio I believe he’d be lacking some other required components and setup.

00:13:45 – Brian (K6BPM) began by trying to understand the two devices and interpret what Jim is trying to accomplish. Most digital mode software out there requires a sound device that can handle input and output to act as a mic and speakers. The conversation was joined by Levi (K6LCM) and Eric (K6HMD) and all had comments and ideas about digital modes basics and how Jim might get the results he’s looking for. You can listen to or download the audio for the net here.

Tune in to the SBARC Technical Mentoring and Elmering Net next Thursday at 8:00 PM or 2000 Hrs  and see what interesting questions will arise or ask some of your own! All club members and visitors are encouraged to check in to the Technical Mentoring and Elmering net each week and join in with questions and /or answers to and contribute the knowledge of new and seasoned amateur radio operators alike.

Note: The time stamp at the beginning of each topic was recorded using Windows Media Player and the downloaded Mp3 audio archive of the net for 5/21/15 found here.

The Technical Mentoring and Elmering net on Thursday 5/21/15 was lightly attended compared to most with 6 check-ins, 2 side responders and net control (K6HWN). Thoughts are that some regulars may have gotten a head start on the Memorial Day weekend.

10:15 First up, Shackmaster Dave had an idea about extending Glenn’s (WZ6WZ) 220 beam antenna to Santa Barbara. The background is that Glen has already installed a 220 transceiver and beam antenna pointed right at 224.08. The question is if they (in Lompoc) can hear the 19.79? repeater that they might be able to use a single 2 meter transceiver at low power to communicate to Santa Barbara. Glenn didn’t know offhand if they can hear it or not but will do the research and get back to Dave.

13:45 – Hayden (KK6OYV) had an update about the fractional wave (loop) antenna that he’s building. Apparently there is a Yahoo group found here dedicated to the concept that Hayden’s been following and he has visited John’s (AG6LJ) house and seen how great his fractional loop antenna performs. Hayden mentioned that his primary motivation to build the antenna is that his station has a lot of electrical noise and the noise floor of his rig is rather high and the fractional wave antennas are not affected as much by that as other antennas. Today he finished the frame of the antenna and now has to finish installing the capacitor control unit and wind the copper wire (strapping) around the frame. Shackmaster asked Hayden if he already has a quality vacuum capacitor and Hayden said no, he’s not sure what value of capacitor he will use yet. Richard (K8NDS, the inventor of the fractional wave) said the antenna Hayden’s building will get him on 10-20 meters with a 5-100pf variable capacitor but Hayden’s also heard of others using a 10-350pf capacitor and getting as low as 40 meters. He’ll be consulting with Richard on that and keep us informed. For those who might be interested check out Richard’s QRZ page and the Yahoo group mentioned above.

17:00 – Brian (K6BPM) asked if anyone is familiar with SIP (Single Inline Package) resistors which are resistor “packs” with one common lead and 8-10 other leads enabling the user to use one small package to supply a common resistance to many components in the circuit. Brian purchased some dual value 220/330 ohm SIPs and there is no explanation of how they work and he couldn’t measure what should logically be true with a meter. No one really had an immediate answer so he’s going to bring some with the paperwork down to the SBARC Club shack to show Dave and with his help they should be able to figure this out. Stay tuned to future TM&E nets to learn the answer!

33.04 – I (K6FLD) started a discussion about a new special mode we’ve been experimenting with during the ATV Special Modes net occurring every Tuesday night at 8:00 PM. Basically it involves the ability to send e-mail over radio without having to be connected to the Internet. Go to Winlink.org to learn more about this very useful mode that should be of interest to any amateur radio operator. Imagine an emergency or disaster situation where all power, phone and cellular networks are down, maybe after an earthquake. If you have backup battery or other backup power (as all good hams should) you will still have the ability to get communications out via e-mail to inform family members in other areas of your situation and that you’re okay. The basics are that you download a program called RMS Express and install it on your computer (hopefully the one with battery backup). Download the guide here and go through the setup and start composing and sending e-mail over the radio. All that’s required is an interface between the computer and radio such as a Signalink USB and off you go. As a matter of fact, some folks have been successful without the interface by holding their microphone to their speaker during the operation! I won’t go into all the details of how the Winlink network operates but please look into this very important mode at Winlink.org and listen to the audio archive. Other uses have been for mariners at sea communicating with e-mail via radio, campers, explorers etc. in remote areas without internet access.

53:50 – Cyril (AF6GW) checked in and mentioned that some other capabilities had been experimented with using 2 meter packet to send e-mail over a repeater. He didn’t remember exactly all of the details but you can learn more here.

Tune in to the SBARC Technical Mentoring and Elmering Net next Thursday at 0800 and see what interesting questions will arise or ask some of your own! All club members and visitors are encouraged to check in to the Technical Mentoring and Elmering net each week and join in with questions and /or answers to and contribute the knowledge of new and seasoned amateur radio operators alike.

The Technical Mentoring and Elmering net on Thursday 5/14/15 was an informative one with 14 check-ins plus net control (K6HWN). The net began at with Brian’s (K6BPM) announcement that we now have a special list server “discussion group” set up for members (and non-members) interested in emergency communications. The purpose for this is to discuss how SBARC can operate as a club, and how the average amateur radio operator in general can help in the event of an emergency. This is not affiliated with ARES or any other group, nor does it interfere with their mission. As a club, and as licensed amateur radio operators, one of our civic responsibilities is to be prepared to help our community in any way we can. We hope you will join and contribute to the discussion! To join the list simply send a blank email to JoinEmCommList@sbarc.org. Further instructions will be sent to you.

Next Ken (KA6KEN) asked why the 220 repeater (224.08) linked and unlinked to 146.79 (K6TZ) periodically throughout the day. The answer to that question is that we link the 224.08 to K6TZ so that ham’s that don’t have a clear signal to the K6TZ repeater but can hit 224.08 can participate in our nets. The operator keys down a second early to make the connection and is heard on K6TZ. The link is taken down after the nets unless someone needs the link for other traffic. The reason the link is taken down is because other signals from other surrounding areas can interfere and can be an annoyance. The discussion evolved into use of a repeater to control a remote base station and then evolved further into the use of remote station operations. One question asked if it is legal for a technician licensee to operate on a repeater that operates a remote base whose output is on another license class frequency allocation. The answer is no, the technician should not operate out of his license class without supervision no matter how they gain access to it.

Shackmaster Dave(K6HWN) then asked who knew all of the handy and emergency reasons to operate remote base station and it proved to be a lively conversation. You can listen to the audio archive of the net here.

Tune in to the SBARC Technical Mentoring and Elmering Net next Thursday at 0800 and see what interesting questions will arise or ask some of your own! All club members and visitors are encouraged to check in to the Technical Mentoring and Elmering net each week and join in with questions and /or answers to and contribute the knowledge of new and seasoned amateur radio operators alike.